12 Days of Christmas
1-800-345-4545
FREE SHIPPING!
Orders Over $95
Same Day Shipping Before 11 PM ET
0
My Cart
$0.00
Shop By Vehicle
Shop By
Category
All Categories

Rebates
Gift Certificates
My Account
E-Mail Signup
Catalog Request
Help

Clevite MS742AL10

Main Bearing Set 1967-74 Ford 1.6L 4 Cyl Engine

Clevite MS742AL10

695-MS742AL10

jegs shipping
Ships 12/14/16 if Ordered Today
Clevite MS742AL10 Main Bearing Set 1967-74 Ford 1.6L 4 Cyl Engine $66.99
Main Bearing Set
  • 1967-74 Ford 1.6L 4 Cyl Engine
  • Aluminum
  • -.010"

  • Specifications:

    Manufacturer's Part Number:
    MS-742AL-10

    These Tri-Metal 77 engine bearings combine the strength of a copper-lead alloy layer with steel backing and an electroplated babbitt metal. The steel backing provides strength and durability; the babbitt overlay provides the critical surface characteristics of slipperiness and conformability. This ideal design has properties not even found in many original equipment bearings. Clevite offers main bearings, rod bearings and cam bearings in this series.

    H Series -
  • Best to start with when unsure which bearing to choose
  • Medium level of eccentricity and high crush
  • Enlarged chamfers for greater crankshaft fillet clearance
  • Made without flash plating for better seating
  • Use with crankshafts that have oversized fillets
  • Use with engines that run mid-high RPM range
  • Contact patterns should ideally cover 2/3 to 3/4 of the bearing surface

    P Series -
  • Typically the greatest level of eccentricity
  • Rods and mains have high crush for maximum retention
  • Most are fully grooved to maximize oil flow to rod bearings
  • Reduced overlay thickness to prevent overlay fatigue
  • Use where extremely high RPMs cause severe rod bore close-in
  • Use where higher eccentricity is desired to narrow bearing contact patterns

    V Series -
  • This series essentially duplicates Clevite's former Vandervell parts
  • Typically low to medium eccentricity
  • Not available with oversized chamfers
  • No flash plating on the steel back
  • All Clevite main bearing sets use a single-piece thrust bearing
  • Narrowed parts available to accommodate increased crankshaft fillet clearance
  • Lead-indium overlay offers slightly better conformability

    M Series -
  • These are special purpose bearings having a nominal .005" thick Babbitt lining on a hardened steel back
  • They are intended mainly for Blown Fuel engines where severe crankshaft deflections cause edge loading of the bearings
  • Under these operating conditions bearing service life will be very short
  • Frequent inspection and replacement is recommended


    Part Number Key
    • H - High-Performance
    • HD - High-Performance bearing with dowel hole
    • HK - High-Performance bearing with moly/graphite coating
    • P - Standard Clevite 77 tri-metal bearing
    • M - Blown Fuel Engine bearing for severe crankshaft deflections & edge loading
    • N - High-Performance Narrowed for greater crankshaft fillet clearance
    • HG - High-Performance full angular grooved bearing
    • V - High-Performance with Lead Indium overlay (On Main Sets this indicates partial groove also)
    • VG - High-Performance with Lead Indium full angular grooved bearing
    • D - Bearing has a dowel hole
    • K - Tri-Armor coated bearing
    • X - Bearing has .001 more oil clearance than standard
    • XX - Bearing has .002 more oil clearance than standard
    • A or AL - Indicates Aluminum bearing material

    Note: Clevite main and cam bearings are priced as sets; rod bearings are priced each.

  • Does Clevite MS742AL10 fit your vehicle?

    Narrow Results

    1967-1968 FORD CORTINA

    • CC: 1599
    • Liter: 1.6
    • SubModel: BASE
    • CUI: 98
    • EngineType: L4 ( 1.6 L / 98 )

    1967 FORD CORTINA

    • CC: 1499
    • Liter: 1.5
    • SubModel: BASE
    • CUI: 92
    • EngineType: L4 ( 1.5 L / 92 )

    1964 FORD CORTINA

    • CC: 1498
    • Liter: 1.5
    • SubModel: GT
    • CUI: 92
    • EngineType: L4 ( 1.5 L / 92 )

    1969-1974 MORGAN 4/4

    • EngineType: ALL
    • SubModel: ALL

    1969 FORD CORTINA

    • CC: 1599
    • Liter: 1.6
    • SubModel: BASE
    • CUI: 98
    • EngineType: L4 ( 1.6 L / 98 )

    1970 FORD CORTINA

    • CC: 1599
    • Liter: 1.6
    • SubModel: BASE
    • CUI: 98
    • EngineType: L4 ( 1.6 L / 98 )

    1963-1966 FORD CORTINA

    • CC: 1498
    • Liter: 1.5
    • SubModel: BASE
    • CUI: 92
    • EngineType: L4 ( 1.5 L / 92 )

    1967-1971 TVR VIXEN

    • EngineType: ALL
    • SubModel: ALL

    1980-1981 MORGAN 4/4

    • EngineType: ALL
    • SubModel: ALL

    1971-1972 MERCURY CAPRI

    • CC: 1599
    • Liter: 1.6
    • SubModel: BASE
    • CUI: 98
    • EngineType: L4 ( 1.6 L / 98 )

    1971-1973 FORD PINTO

    • CC: 1599
    • Liter: 1.6
    • SubModel: BASE
    • CUI: 98
    • EngineType: L4 ( 1.6 L / 98 )
    Items You Need