Jegs Cyber Week Specials
1-800-345-4545
FREE SHIPPING!
Orders Over $95
Same Day Shipping Before 11 PM ET
0
My Cart
$0.00
Shop By Vehicle
Shop By
Category
All Categories

Rebates
Gift Certificates
My Account
E-Mail Signup
Catalog Request
Help

Crane Cams 114102

PowerMax Hydraulic Flat Tappet Camshaft & Lifter Kit
Lift: .378''/.401''
Duration: 244°/254°
RPM Ran

Crane Cams 114102

271-114102

jegs shipping
FREE Shipping
Ships 12/05/16 if Ordered Today
Crane Cams 114102 PowerMax Hydraulic Flat Tappet Camshaft & Lifter Kit
Lift: .378''/.401''
Duration: 244°/254°
RPM Ran
$210.59
PowerMax Hydraulic Flat Tappet Camshaft & Lifter Kit
Lift: .378''/.401''
Duration: 244°/254°
RPM Range: 500-4000
C.A.R.B. Approved*

Crane Cams 114102 Details

Chevy 262-400ci Small Block 1955-98

Crane PowerMax emissions legal cams produce amazing increases in torque, horsepower and throttle response while extending the rpm powerband of computer controlled performance passengers cars and light trucks. PowerMax Emissions cams also permit full function of stock engine control computers. Plus, they work great with aftermarket performance chips.

*Note: 50-State Legal. This camshaft has been granted a California Air Resources Board (CARB) exemption (an ''EO'' number), or is a direct or consolidated replacement part. It is 50-state legal, per the manufacturer's application guide.

**Note: For 1981-87 car and 1981-92 truck applications.

***Note: In order to use these camshafts in 1955-57 265ci blocks, it is necessary to machine a small groove in the rear main journal of the cam to allow oil flow to the top of the engine.

****Note: Beginning in 1987, most of the V-6 and V-8 engines were equipped with hydraulic roller camshafts. There are differences in the block to accommodate a cam retention thrust plate and the anti-rotation mechanism for the lifters. These blocks are identifiable by bolt holes for a cam retention plate under the upper timing sprocket, as well as bosses and tapped holes in the lifter valley for lifter retention hardware. The camshafts on these engines have a step nose and smaller bolt circle on the front of the cam. An earlier model camshaft may be used in these blocks by using the appropriate timing chain set and adding a thrust button when using a roller cam.
1988-99 Chevrolet 305 and 350 V-8 engines (and some 1987 350 V-8 engines) use a different configuration camshaft core than the 1955-87 engines and cannot be interchanged.

BRUTE LOW END TORQUE, GREAT FOR STANDARD 267/4.4L AND 305/5.0L ENGINES. (50 STATE LEGAL IN 1981-87 CAR AND 1981-92 TRUCK 267-305ci APPLICATIONS ONLY. C.A.R.B. E.O. D-225-19)

Grind Number: 2010
Operating Range:500-3500 RPM
Duration Advertised:244° Intake / 254° Exhaust
Duration @ .050'' Lift:184° Intake / 194° Exhaust
Valve Lift w/1.5 Rockers:.378'' Intake / .401'' Exhaust
Lobe Separation Angle:104°
Max Lift Angle:104° ATDC Intake / 104° BTDC Exhaust
Open/Close @.050'' Cam Lift:Intake - (12°) ATDC (opens) / 16° ABDC (closes)
Exhaust - 21° BBDC (opens) / (7°) BTDC (closes)

Items You Need