800.345.4545
Call Our Support Line
24 Hours / 7 Days a Week!  
FREE SHIPPING!
Same Day Shipping Before 11 PM ET
0
My Cart
0
$0.00
Shop By Vehicle
Shop By
Category
Close Menu
Shop By Vehicle
Top Categories
All Categories

All Categories


Free Catalog
E-Mail Signup
My Account
Track Order
Gift Certificates
Rebates
Help

Eastwood 10207Z

Lab-Metal 24 Ounces

Eastwood 10207Z

352-10207Z

ORMD Item - Ground Shipping Only
jegs shipping
Estimated ship date 11/28/17 if Ordered Today
Easy Returns
Easy Returns
Lowest Price Guarantee
Lowest Price Guarantee
Eastwood 10207Z Lab-Metal 24 Ounces $29.99
Lab-Metal
  • 24 Ounces

  • Specifications:

    Manufacturer's Part Number:
    10207Z

    Lab-metal is great for filling dents in metal and non-metal parts. It is a ready to use, aluminum filled repair and patching compound. No 2 component mixing or measuring, so there is no wasted product. No heat, special tools or specialized skills are necessary for use either. Lab-Metal will not shrink, crack or peel and is not affected by mild acids, gasoline, oil or petroleum solvents. Readily adheres to virtually any clean surface and no catalyst needed, so it's easy to apply. Use the Lab Solvent to smooth the Lab Metal to a glass smooth surface to minimize sanding.

    Features:
  • Aluminum-Filled, 1-Part Repair Putty
  • Fills Dents & Flaws Easily & Economically
  • Can Be Milled, Chiseled, Drilled, Sawed, Tapped & Machined
  • No Catalyst Needed, So It's Easy To Apply

  • 10207Z - Eastwood Lab Metal is rated 3.4 out of 5 by 7.
    Rated 5 out of 5 by from Saves a TON of time! Lab Metal is the PERFECT choice for repairing, permanently, rust holes, accidental holes, covering welds and joints, and a lot of other things. It DOES work with powder coating. You can't over heat it though. Heating the oven higher than required to cure the paint will cause Lab Metal to bubble. Use the right temp and it's perfect. I use this to cover large weld joints that may not be perfect, and I don't want to drag out a welder to re-weld the joint. I cover it with Lab Metal and sand it smooth, and it looks perfect when finished and painted. I used it to fill in rust on a 45 year old Wheel Horse mower deck, and it saved me a dozen hours of welding the holes closed. Lab metal filled the holes and looks original when sanded and painted. A real time saver. It takes a little learning curve because it does dry very quickly, so one must continue to paint solvent on it while smoothing it. It's definately not a problem though. I wish it came in different colors that match items I am repairing.
    Date published: 2017-06-27
    Rated 5 out of 5 by from Steel fusion autobody filler Steel fusion body filler is the only real steel filler that will hold up at4000degrees Fahrenheit..and is the strongest autobody filler in d world!..
    Date published: 2017-05-19
    Rated 5 out of 5 by from follow instructions read and follow instructions both products since 1950
    Date published: 2017-02-27
    Rated 5 out of 5 by from Great Product since 1950 Read the instructions and the product will work and use the thinner to clean surface and to thin the product in the can the Lab metal came in.
    Date published: 2015-09-14
    Rated 2 out of 5 by from Difficult to use I bought this to try and restore some pitted pot metal automobile bezels and prepare them for powder coating. Product gets too hard to spread very fast, even when thinned with the solvent. It is also quite difficult to sand and doesn't feather edge very well. Also, it does not adhere very strongly to the sanded, cleaned and media blasted pot metal.
    Date published: 2015-08-18
    Rated 1 out of 5 by from Not for use when powder coating metal! This product will not take the heat in the oven for curing powder coating! Look at my pictures. It looks like I powder coated over rust bubbles. The over all metal dash looks good from a distance, but look closer!!
    Date published: 2016-03-11
    Rated 1 out of 5 by from Another product that fails to perform as stated... Must dilute heavily with solvent to make workable. Instructions state that a 1/16" layer needs 2hrs to cure, so I filled in a dent on a gas tank with four 1/16" layers that I let cure for a FULL DAY each. After four days of patient curing in a heated/insulated shop, I did a final sand in preparation for powder coating. Instructions state that product is good for a 20min trip through the oven @ 420deg, and my powder only needed 12min @ 400deg, so everything should've been kosher. After just 5min in a 400deg oven, the product had outgassed so badly it looked like I powder coated over an Alka Seltzer... One of the bubbles was so big it looked like a pencil eraser sticking halfway through the finish. Fact of the matter is, if this product cannot withstand even 5min in the oven after following the application instructions to a tee, then it CANNOT be powder coated, so you may as well do your repair work with Bondo and simply paint it. I believe I speak for powder coaters everywhere when I say we simply don't have time to completely re-do projects because one of the products we used along the way failed to perform as advertised. Epic FAIL...
    Date published: 2014-11-26
    • y_2017, m_11, d_23, h_24
    • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
    • cp_1, bvpage1
    • co_hasreviews, tv_0, tr_7
    • loc_en_US, sid_10001_10001_1431758, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs
    Items You Need

    Before you leave us... Receive a free catalog or join our email list

    Sign up to receive our catalog or subscribe to our email list now to see our exclusive email only specials, new products, and offers!

    Request CatalogJoin Email List