Black Friday
Call Our Support Line
24 Hours / 7 Days a Week!  
Same Day Shipping Before 11 PM ET
My Cart
Shop By Vehicle
Shop By
Close Menu
Shop By Vehicle
Top Categories
All Categories

All Categories

Free Catalog
E-Mail Signup
My Account
Track Order
Gift Certificates

JEGS Performance Products 80083

Tubing Beader Fits 5/8" and Larger Tubing

JEGS Performance Products 80083


jegs shipping
FREE Shipping
Estimated ship date 03/05/18 if Ordered Today
Easy Returns
Easy Returns
Lowest Price Guarantee
Lowest Price Guarantee
ON SALE - $19.50 OFF
JEGS Performance Products 80083 Tubing Beader Fits 5/8" and Larger Tubing $110.49
Tubing Beader
  • Fits 5/8" and Larger Tubing
  • Up to 0.050" Wall Thickness
  • Minimum I.D. of 5/8"

  • JEGS Performance Products 80083 Details

    Tubing Beader

    • Forms a bead approximately 3/32" tall, 3/16" wide and 5/16" from the end of the tube (measured from the end of the tube to the center of the bead)
    • Fits 5/8" and Larger Tubing
    • Up to 0.050" Wall Thickness
    • Minimum I.D. of 5/8"
    • Designed to be mounted in your vise

    Apply a professional looking and quality bead to the end(s) of the tubing that you are using in your turbo, heating/cooling system or any other tubing on the vehicle that requires a bead. JEGS Tubing Beader forms a bead approximately 3/32" tall, 3/16" wide and 5/16" from the end of the tube (measured from the end of the tube to the center of the bead) on most metal tubing with up to 0.050" wall thickness and a minimum I.D. of 5/8". Designed to be mounted in your vise.

    80083 - JEGS Tubing Beader is rated 3.6 out of 5 by 8.
    Rated 5 out of 5 by from Worked great for turbo tubing I used it to bead 2.25" turbo tubing and it worked great. Read the reviews so I mostly disassembled it and made sure everything was well lubed before I started. I found that I had to clamp it in the vice at an angle in order to clear both the tubing and still be able to crank the handle- no big deal. The tubing was fairly thick so I went easy by tightening fairly firm on the fist pass, then progressively tightened more on each of the following go-arounds. My tubing took 3 passes for a good bead. I never had a binding issue, just had to take it easy and ensure the tubing stayed flush as it rotated. I think some people may be trying to do too much at once or they didn't lube it well if it's binding on them. Good tool for the money.
    Date published: 2017-10-04
    Rated 5 out of 5 by from Works fine Pull it apart, clean it, deburr it and grease it. Works great ! I used it on mild steel, stainless and aluminum.
    Date published: 2017-02-15
    Rated 5 out of 5 by from Works great! I bought this a month ago after considering it and the Earl's setups which make you buy a one for every size tube and ends up over $400 for a set. The bead roller from Jegs is exactly what I needed to do all my aluminum tubing for my rear turbo setup. It made excellent beads for my 2", 1.25",1" and 5/8" tubing I used, all in one machine. Great product.
    Date published: 2016-01-08
    Rated 4 out of 5 by from Great tool for the money I bought this to do some intercooler piping. Used it on 2.75 x 060 aluminum. Works much faster than welding a bead around the end. My only complaints are that the handle should be offset more so that it will sit in a vice properly. And it would be nice if it came with some instructions. It would be really nice if it had a wider flange to keep the pipe square, but again, considering that this is about 1/3 the cost of other bead rollers I can live with it.
    Date published: 2014-11-02
    Rated 3 out of 5 by from Size discrepancy It will not roll beads onto 5/8 tubing. Small roller IS 5/8 dia. Smallest tube capacity is 3/4". Someone needs to correct the description because I needed to roll 5/8 tube beads and it won't do as advertised.
    Date published: 2016-02-02
    Rated 3 out of 5 by from Prior to use.... Prior to actually using this item, I highly recommend completely disassembling and acknowledging the poor construction and address it accordingly. The bearings are very low quality oil bronze sleeves which will eventually bind, they should be pulled cleaned and greased with a higher quality lubricant. Then lube all gears and various contact surfaces. Upon reassembly, be sure to apply some sort of thread lock on all the set screws because they will walk out. The hole drilled in the center of the bead form is off, also off center re-drilling is not an option due to the type of steel it was made with, I had to address the off center bead form by flattening the shaft it rides on. For the price its worth it so long as you're ok with the added warranty voiding hassle.
    Date published: 2015-06-14
    Rated 2 out of 5 by from Junk I had to make 12 beads. After the first two it started to fail. Brass bushings on the one side and not the other. Lubed the heck out of it, but still would bind horribly on the non bushing side. If they just put bushings on both sides it would be fine. It was a bit more than the $80 russel's one so I thought it might be worth a try. It made the beads slower and slower as I went along. It also did not come with the face gaurd either. Cheap overpriced garbage. Buy it if you need to use it once and toss it, or if your rolling beads in super thin wall tubing (even though it says up to .05). Too bad Harbor Freight does not carry this. Then it would be priced right.
    Date published: 2017-02-26
    Rated 2 out of 5 by from Purchased due to price Turning handle reviled tight spots. Disassembled it and found some metal shavings and some dry bearing. Cleaned parts and lubricated bearings and gears now turns smoothly. Took some time to learn how to operate tool, now after 3 rd time am very happy with purchase. If you are a hobbyist like me then I would recommend this tool. Thanks Jegs!
    Date published: 2015-12-03
    • y_2017, m_11, d_23, h_2
    • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
    • cp_1, bvpage1
    • co_hasreviews, tv_0, tr_8
    • loc_en_US, sid_10001_10001_1411298, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs

    Before you leave us... Receive a free catalog or join our email list

    Sign up to receive our catalog or subscribe to our email list now to see our exclusive email only specials, new products, and offers!

    Request CatalogJoin Email List