Quick Fuel P-1050-34 - Quick Fuel Professional Series 4-bbl Carburetors

Quick Fuel #793-P-1050-34

Pro 1050cfm Drag Race Carb

Down leg boosters

3-circuit

Accessories

Share |

Complete list of Quick Fuel Professional Series 4-bbl Carburetors

Details
Overview
Accessories

Quick Fuel P-1050-34 - Quick Fuel Professional Series 4-bbl Carburetors Details

4150 Model with 4500 Base

This carburetor is a standard 4150, but the throttle body bolt pattern is drilled for a 4500 flange. Spacer adapter #793-300-4145-1AL is included with this carburetor.

Special Instructions
Designed to fit 4500 intake manifolds, it is important to use the transition spacer provided with this carb. The spacer tapers from the wider bore of a 4500 intake to the small bore centerline of a conventional 4-bbl, and it solves potential problems related to mounting one of these carburetors directly to a 4500 flange.

The photo below shows a 4500 flange gasket positioned on the throttle body as it would be if the carburetor was mounted directly to the intake without the spacer/adapter. A couple of problems are evident:

All 6 throttle body mounting screws are exposed to the intake manifold opening. Although these screws seldom loosen/fall out during normal operation, it is not worth the risk to leave them exposed.

Though not all mounting flanges are as wide as the flange gasket, most are fairly close to the gasket width so possible interference issues emerge:

The throttle stop arm on the throttle shaft can and often does hit the intake manifold.

A 50cc pump housing will hit the intake manifold due to its proximity to the intake flange.

These potential mishaps are all avoided by using the transition spacer/adapter. If you choose not to use it, it is your responsibility to take corrective steps to prevent these problems which could damage an engine.

For Racers Who Don't Compromise Performance

Main Body

All aluminum (upgrade from existing designs)

Tumbled finish for a high luster that protects against contaminants

Recessed air bleeds out of air stream to improve airflow

Raised accelerator pump squirter nozzle boss also out of air stream to reduce the possibility of high-speed pullover or "dribbling"

Race-only boosters with larger-than-conventional inside & outside diameters, which results in a highly-efficient race engine that has a more uniform fuel curve and is easier to tune

Metering Blocks

CNC-machined from solid aluminum

4 (4150 Models) or 5 stages of emulsion provide the ultimate tuning to customize a race engine's fuel curve to exact specifications, achieving maximum power levels throughout the intended RPM range

Emulsion bleeds are threaded and changeable

Stainless steel idle mixture screw with a superior nylon seal that won't deteriorate

Machined internal passages ensure consistent performance and eliminate the chance of porosity

Throttle Body

CNC-machined die-cast aluminum body designed for competition use

Strengthening ribs reinforce typically weak areas to prevent potential warping or breakage

Thick cross-sectional area guarantees excellent sealing between throttle bodies, lengthening the venturi to help extend the RPM operating range

Teflon-coated throttle shafts with Teflon ribbon bearings provide smooth, precise throttle operation and keep dirt from migrating into throttle body and out of throttle shafts

Mechanical secondary carbs have the Quick Link Secondary Opening System that enables rate adjustment simply by changing links (available opening rates: 40%, 60%, 1:1)

Mechanical secondary carbs also have adjustable secondary airflow cam brackets that allow better idle tuning with race-oriented camshaft profiles

Fuel Bowls

Die-cast aluminum bowls with additional capacity

Unique & patented Fuel Chute directs incoming fuel to the fuel already in the bowl instead of spraying it in the air above fuel level, which greatly reduces fuel aeration & foaming and ensures main metering jets aren't exposed to air pockets

Internal baffles prevent unstable float levels caused by fuel slosh

Shatterproof sight window on 1050, 1150, and 1250 cfm carburetors

-6AN inlet fitting with O-ring on gas applications

-8AN inlet fitting with O-ring on alcohol applications

Floats based on application, i.e. Drag Race Carbs have notched floats & secondary jet extensions