Trans Dapt 9906 - Trans Dapt Performance Products Motor Mounts, Pads & Kits

Don't have your engine where you'd like it? Then check out these motor mounts for some V8 swaps. Part numbers 969-4100 and 969-4606 offer V6 options. Most mounts require no welding and bolt right on, yet some do require additional OE parts.

Chevy
4810 (without pads) Universal Crossmember Motor Mounts for small block Chevy 265-350, big block Chevy 396-454, and frame rails from 24"-37" wide. Center to center between perches is 16-1/8".

9906/9926 For small block Chevy 283-350 V8 into any 2WD S10, these bolt directly to 2.8L V6 mounts. 2.2/4.3L trucks use 9906 only. Hedman Hedders 500-69520 recommended. 9926 without pads.

4606 For 4.3L Chevy V6 into any 2WD 2.2/2.8L S10 (use stock T4/T5 or TH350 transmission), these bolt directly to stock 2.8L V6 mounts.

4689 For small block Chevy V8 into 2WD S10 with TH350, the frame mount plates and hardware are included. Chevy 350 mounting pads and shells are required to complete installation (weld in). Hedman Hedders 500-69490 recommended.

4406 For small block Chevy 283-350 V8 into any 4WD S10, these bolt directly to stock 2.8L V6 mounts.

4516 For LS1/LS6 and Vortec 4.8/5.3/6.0L V8 into S10, these bolt directly to stock 2.8L V6 mounts.

4592 For LS1/LS6 and Vortec 4.8/5.3/6.0L V8 into a vehicle set up for a small block Chevy V8. Replacement mount pads 969-9525.

4100 For Chevy V8 or 4.3L V6 into Jeep CJ series (CJ-2, 3A, 3B, 5, 6, CJ-7), the brackets and pads are included, and welding is required. Replacement mount pads 969-9314.

4566 For small block Chevy into 1987-95 Jeep YJ Wrangler, the bolt-to-frame crossmember requires no welding. Replacement mount pads 969-9525.

9596 Small or big block Chevy V8 into 1964-72 GM Intermediates: For any 1958-Up Chevy V8 into a 1964-72 Buick Special, Skylark, Grandsport; Oldsmobile F85, Cutlass, 442; or, Pontiac Tempest, LeMans, and GTO, this kit includes motor mount brackets, hardware, and instructions (no welding required). Note that additional GM parts are necessary to complete installation.

4686 For small block Chevy V8 into Chevy Vega/Pontiac Astra (will not fit Monza chassis), the complete front and rear mount kit includes motor mount brackets, bushings, plates, and rear crossmember for automatic transmission (TH350 only). Replacement mount pads 969-4684.

Ford
9716 (without pads) For Ford 289-302 into 1982-92 2WD Ford Ranger, some welding is required.
Trans Dapt Oil Filter Relocation Kit (969-1113) and Ford parts are needed to complete installation. Hedman Hedders 500-89500 recommended. Replacement mount pads 969-9717.

9717 These are replacement pads for 969-9716.

9720 For Ford 429-460 into 1965-79 2WD Ford F-100, F-150, F-250, and F-350 (not for Lincoln motors), the mount brackets and bushings are included, no welding required.

9433 For Ford 429-460 into 1967-69 4WD Ford F-250 and 1978-79 Ford F-150 and Bronco (not for Lincoln motors), only mount brackets are included; other Ford parts required to complete installation.

Chrysler
4565 For Mopar B/RB into 1972-87 2WD Dodge truck. Replacement mount pads 969-4220.