ATK Engines HP79C-EFI High Performance Crate Engine Small Block Ford 302ci / 300HP / 336TQ
059-HP79C-EFI
Product Q&A
View Now
Complete Engine
ATK Core Return Process
JEGS and ATK appreciate your business and want to ensure that your core return is as smooth as possible.
Please CLICK HERE for ATK Core Return Process
NOTE:
- Core return can be any Small Block Ford 302ci engine
Engine Specifications
This 302 engine is designed to have great street manners, and work with most stock components.
- Horsepower: 300 hp
- Torque: 336 lb/ft
Block Information:
- Seasoned OE roller block
- Bore/Stroke: 4.040" x 3.000"
- Displacement: 302ci
Rotating Assembly:
- Crankshaft: OE cast 1 piece seal
- Balance: 50oz external balance
- Rods: OE steel rod 5.090" stock bolts
- Compression Ratio: 9.1:1
- Pistons: Hypereutectic
- Rings: Moly
Camshaft Specs:
- Camshaft: Hydraulic roller
- Cam Duration @ .050": Intake 219 / Exhaust 219
- Cam Lift: Intake .498" / Exhaust .498"
- Lobe Separation Angle: 112lsa
- Timing Chain: Double roller
Cylinder Head Information:
- Cylinder Heads: OE E5TE/E7TE cast iron
- Combustion Chamber: 62cc
- Valve Size: 1.77" Intake / 1.46" Exhaust
- Rocker Arms: Stamped steel 1.6 ratio pedestal mount
Oil Pan Information:
- Oil Pan: Front sump or dual sump (Fox Body)
- Oil Pump: Melling standard volume
Recommended Components
- Exhaust: 1-5/8" Headers
- Firing Order: 13726548
- Octane: 91+
- Oil: 10W30 (Conventional / Non Synthetic)
- Oil Filter: Wix or K&N
- Spark Plug Gap: .035"
- Stall Converter: Stock
- Timing: 34-36 Degrees (Vacuum port plugged on carburetor)
- Balancer: External 50oz
- Carburetor: Edelbrock Thunder Series 650cfm #350-1806
- Distributor: Pro Billet MSD #121-8352 (Requires melonite or steel gear) or factory EFI distributor
- Flexplate: Flywheel: External 50oz
- Intake Manifold: Weiand dual plane #925-8020WND or Factory 1987-1995 Mustang EFI intake
- Fuel Injection: Will not work with Ford factory speed density EFI or F-Series Trucks, Broncos, or Vans. If installed in a 1987-1995 Mustang you must tune the ECM
- Fuel Pump: Holley Mechanical 110gph #510-12-289-11 or factory electric in installed in 1987-1995 Mustang
- Spark Plugs: Autolite #417-24
- Spark Plug Wires: 8mm
- Water Pump: OE per application/factory
Disclaimer: The parts listed are ATK's recommendations of parts to be used to obtain the power figures listed. Power figures can vary based on parts used by the end user. Some modifications to the vehicle may be required using these and or other aftermarket parts.
Engine Break-In Procedure
Use or break-in oil or conventional (non-synthetic) 10w30 oil with zinc additive for the first 500 miles of operation. Do not drive for long periods at any single speed, always vary your speed. Do not tow a trailer or put other heavy loads on the vehicle. It is best to avoid long periods of idling during this period. Check the engine oil and coolant levels daily.
Engines with flat tappet hydraulic cams only - Run the engine between 2,000 and 2,500 RPM's, with no-load on the engine for the first 30 minutes. Let the engine cool down completely and repeat process 2-3 more times. Do not idle the engine for any extended period at this time, this is critical to break in the camshaft.
At 500 Miles change the engine oil and filter using conventional (non-synthetic) oil with a zinc additive. Check fuel and ignition settings, adjust valves (where applicable). Drive the next 500 miles normally, without high RPM's (below 5000 RPM), hard use, or extended periods of high loading or long periods of idling.
Change the oil and oil filter again at 1,000 miles. Continue using conventional (non-synthetic) oils and zinc additive, until about 4,000 miles. At that point, you may run a quality 10w30 synthetic oil if you choose. Use of oil with zinc or a zinc additive for the life of your engine is recommended.
Specifications:
Does this come with the intake?
I have a 1982 Ford Mustang Gt the car was put in storage for over 30 years and now needs to have the motor replaced the original engine only has 16K on it. I’m looking for 5.0L that will bolt up to the manual 4 speed that came with the car pushing 350 HP
Would this work for my 95 mustang GT eft with t-5 5 speed
Will this motor fit into a 1982 Mustang GT with a 4 speed manual transmission.
Does this include engine wiring harness and the computer
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.