Items You Need
Block:
- Seasoned 454 ci Block (+.060 in.)
- 4-Bolt Main
- 1-Piece Rear Main Seal
- Mechanical fuel pump provision
- Square and Parallel Decked
- Align Honed Main Bearing Bore
- Cylinders are Sonic Tested for Thickness
- Cylinders Honed on a Computer-Controlled Machine to within .0002 in. for Straightness and Roundness
Rotating Assembly:
- Forged Crankshaft
- 4.250 in. Stroke
- 6.385 in. Length Forged H-Beam Connecting Rods
- Internal Balance
- Forged Pistons
- 8.8:1 Compression Ratio
Cylinder Heads:
- Blueprint Aluminum Cylinder Heads - 138-PS8013
- Hardened Retainers and Springs
- 2.300 in. Intake Valves
- 1.880 in. Exhaust Valves
- 119 cc Combustion Chamber
- 316 cc Intake Runners
- 124 cc Exhaust Runners (Exhaust port raised .300 in. over OEM casting)
Camshaft Specs:
- Hydraulic Roller Cam
- Duration at .050 in. Lift: 242 Degree Intake / 248 Degree Exhaust
- Lift: .540 in. Intake / .560 in. Exhaust
- Lobe Separation: 114 Degree
Timing Specifications:
- Initial Timing: 10-16 Degree
- Total Timing: 32-34 Degree
- Spark Plugs: NGK BKR5E with a .035 in. Gap Recommended (NOT Included)
Base Model Long Block Includes:
- Assembled Short Block Painted Ford Blue
- Aluminum Cylinder Heads
- Camshaft
- Harmonic Balancer
- Timing Set
- Timing Cover
- Oil Pump and Pickup Tube
- Dual Sump Oil Pan
- Valve Covers
- Dyno Test Sheet
Additional Notes:
- Built to accept power adders (supercharger, turbocharger, nitrous)
- Requires Internally Balanced Balancer and Flexplate/Flywheel
- Recommend 2200-2300 RPM Stall Converter
- Recommend 850 cfm Carburetor
- Recommend Fuel: 87 Octane if naturally-aspirated
- Recommended Oil: 10W30, Non-Synthetic
- Not for EGR Applications
Engine Break-In Procedure
Use or break-in oil or conventional (non-synthetic) multi-viscosity oil with zinc additive for the first 500 miles of operation. Avoid hard acceleration for sustained periods. Periodically change the engine speed while driving to help seat the rings. While the engine is running, be sure to check oil pressure and coolant temperature, and check for fluid leaks, such as oil, transmission fluid, fuel, and coolant/antifreeze. Also listen for any unusual sounds. Should you hear an unusual sound, shut the engine off, check for the source, and correct it.
Engines with flat tappet cams only - Start the engine and bring it to 2,000 RPM. Get the engine running smoothly. Then vary the engine speed from 1,800-2,200 RPM in a slow acceleration/deceleration cycle for 30 minutes. This is necessary to provide adequate oil splash and lifter rotation to properly mate each lifter to its lobe.
At 500 Miles change the engine oil and filter using conventional (non-synthetic) oil. After 6,000 miles, synthetic oils can be used in your engine. For flat tappet cam engines, continued use of oil with zinc or a zinc additive for the life of your engine is recommended.
Specifications:
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.