Blueprint Engines GM LS3 EFI Retrofit Dress Crate Engine with Accessory Drive System [530 HP, 495 FT.-LBS]
138-PSLS3760CTFB
Product Q&A
View Now
![GM LS3 EFI Retrofit Dress Crate Engine with Accessory Drive System [530 HP, 495 FT.-LBS]](http://www.jegs.com/images/photos/100/138/138-psls3760ctfb.jpg "GM LS3 EFI Retrofit Dress Crate Engine with Accessory Drive System [530 HP, 495 FT.-LBS]")
Dress Engine w/Accessory Drive
Installation Notes
- Not designed for late model applications that were originally equipped with factory fuel injection
- The engine will require a controller kit it is not included
- This engine uses a 58x reluctor wheel on the crankshaft and a 4x cam sensor located in the timing cover
- Uses EV6 type fuel injector
- Not for EGR
Recommended Stall Converter: 2200+ RPM
Recommended Fuel: 91 Octane
- New GM 6.2L aluminum block
Rotating Assembly
- Nodular Iron Crankshaft: 3.622 in. Stroke
- Forged Connecting Rods: 6.098 in.
- Hypereutectic Pistons
- 10.7:1 Compression
- Internally Balanced (Balancer Included)
Cylinder Heads
- LS3 Aluminum
- Combustion Chamber: 68 cc
- Intake Valve: 2.165 in.
- Exhaust Valve: 1.600 in.
Camshaft Specs
- Hydraulic Roller
- Duration at .050 in. Lift: 225 Intake, 238 Exhaust
- Lift: .612 in. Intake, .585 in. Exhaust
- Lobe Separation: 113 Degrees
Other Features
- GM LS3 Intake Manifold, fuel rails, injectors
- Drive-By-Wire throttle body
- GM Hot Rod universal oil pan
- AC Delco coil packs and plug wires
- Firing Order: 1-8-7-2-6-5-4-3
- ACDelco 41-985 spark plugs (.040 in. Gap)
- Includes coil packs, coil wiring harness, crank, cam, coolant, knock, oil pressure, map sensors, and complete accessory drive system (balancer, water pump, alternator, power steering pump, A/C compressor, belt, and all pullies).
Engine Break-In Procedure
Use or break-in oil or conventional (non-synthetic) multi-viscosity oil with zinc additive for the first 500 miles of operation. Avoid hard acceleration for sustained periods. Periodically change the engine speed while driving to help seat the rings. While the engine is running, be sure to check oil pressure and coolant temperature, and check for fluid leaks, such as oil, transmission fluid, fuel, and coolant/antifreeze. Also, listen for any unusual sounds. Should you hear an unusual sound, shut the engine off, check for the source, and correct it.
Engines with flat tappet cams only - Start the engine and bring it to 2,000 RPM. Get the engine running smoothly. Then vary the engine speed from 1,800-2,200 RPM in a slow acceleration/deceleration cycle for 30 minutes. This is necessary to provide adequate oil splash and lifter rotation to properly mate each lifter to its lobe.
At 500 Miles change the engine oil and filter using conventional (non-synthetic) oil. After 6,000 miles, synthetic oils can be used in your engine. For flat tappet cam engines, continued use of oil with zinc or a zinc additive for the life of your engine is recommended.
Specifications:
Are these engine turn key ready?
Will this fix a 2000 s10
What cam comes in it?
Will this fit my 2010 camaro ss?
Will this engine work in my 2001 Corvette?
Will this fit in my 2008 corvette?
Will this fit in a 2002 gmc pickup that has a 5.3
Will this work in a 1997 Camaro that was originally a 6 cylinder car.
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.