Small Block Chevy 262-400ci 1955-98
*Note: 50-State Legal. This camshaft has been granted a California Air Resources Board (CARB) exemption (an ''EO'' number), or is a direct or consolidated replacement part. It is 50-state legal, per the manufacturer's application guide.
**Note: In order to use these camshafts in 1955-57 265ci blocks, it is necessary to machine a small groove in the rear main journal of the cam to allow oil flow to the top of the engine.
***Note: Beginning in 1987, most of the V-6 and V-8 engines were equipped with hydraulic roller camshafts. There are differences in the block to accommodate a cam retention thrust plate and the anti-rotation mechanism for the lifters. These blocks are identifiable by bolt holes for a cam retention plate under the upper timing sprocket, as well as bosses and tapped holes in the lifter valley for lifter retention hardware. The camshafts on these engines have a step nose and smaller bolt circle on the front of the cam. An earlier model camshaft may be used in these blocks by using the appropriate timing chain set and adding a thrust button when using a roller cam.
1988-99 Chevrolet 305 and 350 V-8 engines (and some 1987 350 V-8 engines) use a different configuration camshaft core than the 1955-87 engines and cannot be interchanged.
GOOD IDLE, FOR 350+ CU. IN. MODIFIED ENGINES WITH FREE-FLOWING ABOVE WATER EXHAUST SYSTEMS FOR PERFORMANCE APPLICATIONS IN LIGHT PLEASURE AND SKI BOATS, INCLUDING JET BOATS, 8.75 TO 10.75 COMPRESSION RATIO ADVISED (C.A.R.B. E.O. D-225-18).
|Grind Number:||H-268-2 (Replaces H-272-2)|
|Operating Range:||2000-5000 RPM|
|Duration Advertised:||268° Intake / 280° Exhaust|
|Duration @ .050'' Lift:||218° Intake / 230° Exhaust|
|Valve Lift w/1.5 Rockers:||.459'' Intake / .486'' Exhaust|
|Lobe Separation Angle:||112°|
|Max Lift Angle:||107° ATDC Intake / 117° BTDC Exhaust|
|Open/Close @.050'' Cam Lift:||Intake - (2°) BTDC (opens) / 36° ABDC (closes)|
Exhaust - 52° BBDC (opens) / (2°) BTDC (closes)
The most popular OE camshaft type through the late 1980s, hydraulic lifter profiles can provide a power curve that tops out just over 7000 RPM when used with high-performance hydraulic lifters. Also easy to maintain, hydraulic cams range from aggressive (rough idle) to towing (improved bottom-end torque).
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.