Account Login
Gift Cards
Track Order
Click image to zoom
Manley 13080-8
Representative Image
Product images may differ from actual product appearance.

Manley Super 7° Steel Valve Locks 5/16" (.3110" ) Valve Stem


Ships directly from the manufacturer on 10/28/19
Save $10 off $199, $45 off $499, $100 off $999. Promo Code: FALLFUN exclusions apply

Manley Super 7° Steel Valve Locks 5/16" (.3110" ) Valve Stem $33.99
Out of stock
Super 7° Steel Valve Locks
  • 5/16'' (.3110'') Valve Stem
  • Standard Height
  • Conventional Groove Type
  • 8.3 grams
  • Set of 8 pairs
  • Manley 13080-8 Details

    5/16'' (.3110'') Valve Stem Size

  • Conventional Groove Type
  • Specifications:

    Manufacturer's Part Number:

    The Super 7° Eliminates
    the Retainer Extrusion Problem!

    Manley Super 7° angle valve locks are actually 8°'s! They are designed to work exclusively with Manley's Super 7° retainers. They are heat treated and coated with a black oxide finish for a strong, reliable valve lock. These locks are a favorite of NASCAR and BGN engine builders. Made from the highest quality steel alloy, these locks are thicker than the competitions for greater strength and durability.

    The groove in a valve stem, seemingly unimportant, in reality is vital to the success of a valve's performance. Imperfectly formed grooves, inferior or mismatched locks, and improper retainers can lead to catastrophic failure. The so called ''conventional'' or square groove design has enjoyed enormous success. But the success of a ''conventional'' groove is dependent upon precise machining. First, the surface finish of the groove must be outstanding to guarantee against failure due to residual machining marks. Next, the groove must have a precise .013'' radius in the upper corner. Too small a radius leaves the groove subject to the dangers of a sharp fillet. Too large a radius leaves open the possibility of the groove being abraded in this area by the upper inside edge of the tang of the lock. Also, an oversized radius leaves a reduced horizontal shelf in the groove which is, or should be, the only contact point with the tang of the lock. Contact by the lock in the root of the groove is a disaster waiting to happen. Perfectly formed ''conventional'' grooves with proper locks and retainers will deliver good service. However, there are sub-standard components on the market that can conspire to destroy a correctly machined groove. The essence of the Bead Loc groove is its simplicity and forgiveness. The groove itself is a straightforward .110'' full radius. The contact points with a Bead Loc radius lock are approximately 2 and 10 o'clock, not at the root of the groove. This system affords minimal vertical movement, especially when valve float is present, which means reduced erosion of the valve for enhanced service life. Manley Performance supports both the ''conventional'' groove system and the Bead Loc system with the most extensive line-up of the highest quality locks in the industry.

  • Super 7° angle is actually 8° (Use with Manley Super 7° Retainers)
  • Overcomes the extrusion problem with increased lock thickness
  • Heat treated and black oxide finished
  • Highest quality steel alloy
  • Thicker for greater strength
  • Choose Conventional or Bead Loc groove type

  • Some parts are not legal for use in California or other states with similar laws / regulations

    Motor Vehicles

    WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.


    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

    Electrical Cords

    WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.