ATK Engines HP89C-EFI High Performance Crate Engine Small Block Chevy 350ci / 390HP / 420TQ
059-HP89C-EFI
Product Q&A
View Now
Complete Engine
ATK Core Return Process
JEGS and ATK appreciate your business and want to ensure that your core return is as smooth as possible.
Please CLICK HERE for ATK Core Return Process
NOTE:
- Core return can be any Small Block Chevy 350ci engine, except 1992-1997 LT1 style engines
Engine Specifications:
- Horsepower: 390
- Torque: 420
- Block: 1996-2000 OE roller block 4 bolt main 1-piece seal
- Bore/Stroke: 4.040 in. x 3.480 in.
- Displacement: 350ci
- Crankshaft: OE Reground external balance rear of the crank/internal balance front of the crank
- Rods: OE powder metal 5.700 in.
- Pistons: Hypereutectic 10:1 Compression
- Rings: Moly
- Camshaft: Hyd. Roller
- Cam Specs: 220/224 @50 .528in/.536ex 110 LSA
- Timing Chain: Double Roller
- Cylinder Heads: ATK High-Performance aluminum with 2.020 in. /1.600 ex. valves
- Rocker Arms: Billet aluminum roller rockers 1.6 ratio
- Oil Pan: Rear sump 5qt (not for Chevelles with steering behind crossmember, some corvettes and 62-67 chevy II’s)
- Oil Pump: Melling STD Volume
- Flexplate/Flywheel: Externally Balanced – Pioneer #FRA-159
- Balancer: Internally Balanced – PowerBond #PB1046-N
- Intake Manifold: ATK dual plane intake
- Distributor: HEI (Iron Gear)
- Water Pump: OE long pump
- EFI System: Fitech Go Street EFI 400 HP (throttle body, wire harness and handheld unit included)
- Fuel Pump: Not Provided - must run an electric pump or mechanical fuel pump with Fitech Fuel Command Center
- Spark Plugs: Autolite #3923
- Spark Plug Wires: 8 mm
Engine Info:
- Oil: Conventional / Non Synthetic 10W30
- Oil Filter: Wix or K&N
- Timing: 34-36 Degrees
- Spark Plug Gap: .035 in.
- Firing Order: 18436572
- Octane: 91+
- Stall Converter: 2200-2800
- Exhaust: 1 5/8 in. Headers
Disclaimer: The parts listed are ATK’s recommendations of parts to be used to obtain our power figures listed. Power figures can vary based on parts used by the end-user. It is the customer’s responsibility to verify components will work in their application. Some modifications to the vehicle may be required using these and or other aftermarket parts. . ATK reserves the right to substitute parts used in engines if necessary.
Engine Break-In Procedure
Use or break-in oil or conventional (non-synthetic) 10w30 oil with zinc additive for the first 500 miles of operation. Do not drive for long periods at any single speed, always vary your speed. Do not tow a trailer or put other heavy loads on the vehicle. It is best to avoid long periods of idling during this period. Check the engine oil and coolant levels daily.
Engines with flat tappet hydraulic cams only - Run the engine between 2,000 and 2,500 RPM's, with no-load on the engine for the first 30 minutes. Let the engine cool down completely and repeat process 2-3 more times. Do not idle the engine for any extended period at this time, this is critical to break in the camshaft.
At 500 Miles change the engine oil and filter using conventional (non-synthetic) oil with a zinc additive. Check fuel and ignition settings, adjust valves (where applicable). Drive the next 500 miles normally, without high RPM's (below 5000 RPM), hard use, or extended periods of high loading or long periods of idling.
Change the oil and oil filter again at 1,000 miles. Continue using conventional (non-synthetic) oils and zinc additive, until about 4,000 miles. At that point, you may run a quality 10w30 synthetic oil if you choose. Use of oil with zinc or a zinc additive for the life of your engine is recommended.
Specifications:
Will Doug’s D350 headers fit these heads ? I have a 1978 Corvette with these headers. Anything needed to mount a 700R4 to this engine ? Thanks.
Will the ATK HP89c engine fit in a 1985 firebird with a five speed trans and are there any recommendations for fitment or additional parts that may need to be purchased. Thanks for reviewing my question.
Will this a 1985 CJ& jeep
When looking at the engine, it says that the fuel pump comes with it, but it also says the the fuel pump is not included which one is it does it come with or without the fuel pump?
I’m putting this in a 1989 suburban will my factory transmission bolt up? Will the wiring for the factory T.B.I work? Does it come with a fuel pump?
Will this engine work in a 1989 Chevrolet caprice throttle body? It’s already equipped with a 305 throttle body.
Will this fit a 1983 Oldsmobile Cutlass with minimal alterations?
Will this fit in my 1994 Chevy Silverado. 4 wheel drive
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.