Instant Rebates
Call Our Support Line
24 Hours / 7 Days a Week!  
Same Day Shipping Before 11 PM ET
My Cart
Shop By Vehicle
Shop By
Close Menu
Shop By Vehicle
Top Categories
All Categories

All Categories

Free Catalog
E-Mail Signup
My Account
Track Order
Gift Certificates

JEGS Performance Products 40800

Orange Ignition Control Unit 6,000 RPM

JEGS Performance Products 40800


jegs shipping
Easy Returns
Easy Returns
Lowest Price Guarantee
Lowest Price Guarantee
JEGS Performance Products 40800 Orange Ignition Control Unit 6,000 RPM $29.99
Orange Ignition Control Unit
  • Comparable to Mopar Orange Ignition Box
  • 6,000 RPM

  • JEGS Performance Products 40800 Details

    Electronic Ignition Control Units

      Installation Notes:
    • Case must be grounded. Be sure mounting location (firewall, bracket, or fender apron) is free of rust & paint (sand or wire brush as required) before mounting Ignition Control Unit. Make sure the mounting screws are tight and use Serrated-head screws or external-tooth lock washers to mount the Ignition Control Unit.
    • Coat connector pins with silicone grease. Be sure wiring connector retaining screw is present and snug.
    • Plugs into all Mopar OEM, JEGS, and Mopar Performance wiring harnesses, whether the harness or vehicle was designed for 4 or 5-pin Ignition Control Units. No modifications required.
    • Use with ballast resister. Works with 2-Pin or 4-Pin ballast resistors. Use without ballast resistor will destroy the Ignition Control Unit.
    • Use with OEM or OEM-Spec (oil filled) ignition coil. E-Frame coils are also acceptable. High Performance Coil 555-40105 is also recommended. Coils made for C-D ignitions (MSD, etc) may destroy the Ignition Control Unit. Coil Primary resistance should be no lower than 1.4Ω
    • Pre-startup test (recommended for vehicles that has experienced Ignition Control Failure). Connect a voltmeter between the coil positive (+) and a good ground. Turn ignition key to "run" position. Voltmeter should read between 7.0 and 9.0 volts. If higher turn ignition key off immediately and check ballast resister (resistance - too low 0.5Ω minimum, 1.0Ω recommended for most street applications), ballast wiring, shorted coil, ignition switch wiring, etc.
    • Quick Wiring Check - Disconnect either ballast connector at idle. Engine should stall instantly.

    JEGS offers two options for ignition control on Mopar engines. Choose from the HiRev 7500® control unit with an OEM Appearance & modern electronics inside or the standard Orange control unit. The electrical connector on control unit plugs into all Mopar OEM and Mopar Performance wiring harnesses (both 4 & 5-pin harnesses). A replacement wiring harness and ballast resistor are also available to repair or upgrade the ignition system (sold separately).

    JEGS EZ Kits are designed by JEGS professionals to ensure that you get all the correct parts you need.

    555-40800 is rated 3.0 out of 5 by 2.
    Rated 5 out of 5 by from Did what I wanted it to do Bought this to get rid of a miss in 2nd & 3rd gear. Had a stock ECM .
    Date published: 2014-11-02
    Rated 1 out of 5 by from died after four months I bought this in January, now its April and it left me stranded. I only drive to the local car show once a week, and its two miles away. Do the math. If you buy one, keep a spare!
    Date published: 2015-04-11
    • y_2017, m_11, d_20, h_21
    • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
    • cp_1, bvpage1
    • co_hasreviews, tv_0, tr_2
    • loc_en_US, sid_10001_10001_1327626, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs
    Items You Need
    Items You May Also Consider

    Before you leave us... Receive a free catalog or join our email list

    Sign up to receive our catalog or subscribe to our email list now to see our exclusive email only specials, new products, and offers!

    Request CatalogJoin Email List