Items You Need
Ford
Godzilla
Holley 550-1431 Terminator X MPFI Controller Kit Ford Godzilla 7.3L Features:
- Seamlessly integrates with your 7.3L Ford Godzilla engine for easy installation
- No need for extensive modifications; enjoy a hassle-free setup
- Base calibrations included in the free Terminator X Software, and Handheld Wizard - OEM VVT and Oil pump control pre-configured
- Godzilla Crank Sensor Module included, must be used in-line with factory crank sensor
- OEM Oil pump control and VVT Control built into both Godzilla main harnesses, these features utilize (2) inputs and are pre-configured in the base calibrations.
- Customizable tuning parameters allow you to tailor performance to your specific driving preferences.
- Drive-by-wire (DBW) kits require the use of the specific OEM throttle bodies and throttle pedals: Throttle Body - JL3E-9F991-AA – Throttle Pedal - BR3Z-9F836-D. Other options are listed within instruction manual 199R12525
- Real-Time fuel map learn, takes the guess work out of tuning your base fuel table.
- High Impedance Injector Drivers will safely power most OEM injectors, and Holley EFI Injectors. (Will not control Low Impedance Injectors)
- All of the new Terminator X Max systems utilize the Bosch LSU 4.9 wideband to relay AFR information to the ECU for accurate reading and precise tuning control.
- On-Board 1BAR MAP sensor, is perfect for N/A or Nitrous engine combos. If your combination requires a 2+BAR, we recommend GM 12592525 MAP sensor and Holley 558-416 adapter.
- MAP Sensor vacuum hose adapters (1/8th – 1/4 and 3/16ths)
- 4 Inputs – 12v, Ground, 5v, and Frequency, for things such as additional pressure sensors, or activation triggers for nitrous activation, or a trans brake
- 4 Outputs – Ground, PWM - , for accessories such as; fans, boost control, nitrous control, IAC Kit, and More
- Boost Control – Boost vs Time, Boost vs Gear, Boost vs RPM, Boost vs Speed, Boost Safeties
- Nitrous Control – Single Channel of Wet or Dry, Progressive or Non-Progressive, Rich/Lean Safeties, and target Closed Loop AFR
- Advanced Tables – 4x 1D Tables, 1x 1D per Gear Table, 4x 2D Tables, 1x 2D per Gear Table, can be used for any custom tables you can dream up, such as Flex Fuel Sensor Offset Table, or a custom fuel or oil pressure safety
- On-Board Diagnostic LEDS for: ECU Power – Engine Run – Wideband Status – TPS Calibration – Crank Signal – Cam Signal. Allow you to identify any Critical engine issues at a glance
- The included 3.5-inch Touchscreen Handheld contains a calibration wizard, that allows you to quickly build a base tune for any Godzilla engine. Additionally, the handheld provides internal data-logging and a fully customizable gauge display.
- The compact ECU size allows you to mount it virtually anywhere.
- Plug and play compatible with more Holley EFI accessories such as; analog style gauges, EGT module, as well as 5-inch, 6.86-inch and 12.3-inch Digital Dashes
- Free EFI Tuning Software for complete control of your Terminator X power plant
Holley 550-1431 Terminator X MPFI Controller Kit Ford Godzilla 7.3L Notes:
- Terminator X & Terminator X Max ECUs are designed to be installed with LED lights facing upwards.
- This kit is only for use with Godzilla engines with “dumb” coils (no built in ignitors). There are 2-, 4-channel drivers included that plug into the main harness to drive the coils.
- 2 of the 4 “additional” ECU outputs will be used to control VVT and the Oil Solenoid. These are pre-wired in the main harness and pre-configured in the base calibrations.
- The included crank sensor module (labeled 200R739A) is intended to be connected in-line between the crank connector on the main harness and the crank sensor. The replacement part number for this module is 558-474.
- The harness included with this kit uses the same connectors for CTS/CHT, VVT, and the OIL SOLENOID.
Emissions Note:
This part is only legal for sale and use on Uncontrolled (Non-Emissions Controlled) Vehicles or on vehicles used solely for the purposes of closed competition racing.
CLICK THIS LINK FOR IMPORTANT CARB & EPA EMISSIONS INFORMATION ABOUT THIS PART
Specifications:
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.