Blueprint Engines New Block Casting 350 ci Cruiser Crate Engine
138-BP350CT
Items You Need
Crate Engine
Blueprint 350 ci Cruiser Crate Engine with 9.0:1 compression ratio can be run on 87 octane pump gas. Its camshaft profile provides up to 18 in. of vacuum and is designed to work with a stock torque converter and stock rear-end gears. The oil pan and chrome valve covers and timing cover are included.
Blueprint 350CT Features:
- Power Ratings:
- 341 Horsepower (HP)
- 371 ft.-lbs. Torque (TQ)
- 9.0:1 Compression Ratio
- Blueprint Engine Block:
- New Cast Iron Block
- 4-Bolt Mains
- 4.000 in. Bore
- One-Piece Rear Main Seal
- Provision for Mechanical Fuel Pump
- Right (Passenger) Side Dipstick
- Drilled and Tapped for Mechanical Clutch Linkage
- Rotating Assembly:
- Cast Iron Crankshaft w/3.480 in. Stroke
- Forged 5.700 in. Long Connecting Rods
- Hypereutectic Pistons Provide 9.0:1 Compression
- Internal Front / External Rear Balancing
- Blueprint Aluminum Cylinder Heads (138-H8002K):
- 195cc Intake Runners
- 75cc Exhaust Runners
- 64cc Combustion Chambers
- 2.02 Intake Valves
- 1.60 Exhaust Valves
- Camshaft:
- Hydraulic Roller
- .477 in.Intake Valve Lift
- .471 in. Exhaust Valve Lift
- 202° Intake / 212° Exhaust Duration @ .050 in.
- 115° Lobe Separation Angle
Emissions:
Legal for use on vehicles that were manufactured before emissions control regulations were imposed. These vehicles are considered uncontrolled vehicles and are defined as:
- 1965 and older U.S. manufactured California Certified Vehicles
- 1967 and older U.S. manufactured Federally Certified Vehicles
- 1967 and older Foreign manufactured vehicles
Specifications:
Will this fit in my 95 corvette?
Does this have a warrenty and if so how much
What type of Rocker Arms and the ratio of 138-BP350CT? It comes with a roller cam, are the rockers full roller also?
I have a 78 firebird with factory gm 305 with th350. Will this motor fit with factory mounts?
I have a 1986 (305) El Camino. I want to use the same intake manifold and carb. Will the Blueprint 350 longbloc fit right in?
Would the blueprint 350 5.7 liter 138-BP350CT ENGINE work for a replacement 350 for a 1992 chevy silverado 2 wheel drive with a stock transmission? And would all the old components coming off the old engine work like intake fuel injection pulls system etc
Would the blueprint engine 138-bp350ct work for a 1992 chevy silverado 2 wheel drive stock transmission? And would all the components work like intake fuel injections pulls system etc.??? Thanks mike
Hello, would this engine properly pair with JEGS TH350 Performance Transmission 2WD? If not, what transmission would work? I'm looking to install both in my 1977 Chevrolet C10 Silverado.
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.