0
0
Top Categories
All Categories

Top Categories

All Categories


Shop By Vehicle
Account Login
1-800-345-4545
Gift Cards
Track Order
Help
Click image to zoom
Chevrolet Performance 19367080

Chevrolet Performance SP350/357 Base Engine

809-19367080

Free Shipping Ships

$3,692.38
Chevrolet Performance SP350/357 Base Engine $3,692.38
Out of stock
2 left in stock
QTY
SP350/357 Base 350ci Engine
  • 357 HP @ 5500 RPM
  • 407 ft/lbs Torque @ 4000 RPM
  • Chevrolet Performance 19367080 Details

    SP350/357 Base 350ci Engine

     

    INSTALLATION NOTES:

    • Use the Holley 670-cfm four-barrel carburetor p/n 809-19170092 to achieve the listed horsepower and torque
    • Requires four-barrel carburetor, intake manifold, distributor, spark plug wires, external balance flexplate, water pump and additional components to complete assembly
    • Distributor with melonized steel gear MUST be used with steel camshafts, or engine damage will occur.
    • Some assembly and minor engine tuning required
    • Not intended for marine application

    Engine Break-In Procedure

    Use conventional or break-in oil (non-synthetic) for the first oil change, be sure to check the oil level in the engine and prime the oil system with an engine priming tool. 

    Engines with flat tappet hydraulic cams only - Run the engine between 2,000 and 2,500 RPM's, with no-load on the engine for the first 30 minutes. This is critical to break in the camshaft.

    Drive the vehicle with varying speeds and loads on the engine for the first 30 miles. Be sure not to use a lot of throttle or high RPM.  Run five or six medium-throttle accelerations to about 3000 RPM (40 to 50 MPH), then letting off in gear and coasting back down to 20 MPH. Run a couple of hard throttle accelerations up to about 5000 RPM (55 to 60 MPH), then letting off in gear and coasting back down to 20 MPH.

    Let the engine cool and change the oil and filter using conventional (non-synthetic) oil and check coolant level, top off if necessary. Drive the next 500 miles normally, without high RPM's (below 5000 RPM), hard use, or extended periods of high loading.  Change the oil and oil filter again using conventional (non-synthetic) oil.  Keep an eye on oil level during the first thousand or so miles.

    It would be suitable to use synthetic motor oil after the second recommended oil change and mileage accumulation. 

     

    Specifications:

    Manufacturer's Part Number:
    19367080

    The New Standard for Affordable Small-Block Performance!

    Free Shipping!

    If it's affordable performance you're looking for to power your project car or truck, Chevrolet Performance's SP350/357 delivers! With 357 horsepower and a deep reserve of low-rpm torque, it quickly reminds you why Chevrolet's original 350 small block has been the industry benchmark for decades.

    The SP350/357 leverages the strength of a strong rotating assembly secured in a brand-new block with four-bolt main caps, along with their economical Vortec iron cylinder heads. A roller camshaft optimizes the airflow capability of the cylinder heads which really improves drivability.

    This SP350/357 base engine topped with a Chevrolet Performance dual-plane intake manifold and Holley 670-cfm 4-barrel carburetor all adds up to a 24-horsepower gain over the 350 HO crate engine - and a great, affordable alternative to rebuilding.

    This base crate engine package includes an assembled long block, including the oil pan and valve covers. The perfect foundation for you to finish it off your way, with the ignition system, induction system and accessories.

    SP350/357 BASE TECH SPECS:

    • Engine Type: Chevy Small-Block V-8
    • Displacement: 350ci
    • Bore x Stroke: 4.000'' x 3.480''
    • Block: Cast-iron with four-bolt main caps
    • Crankshaft: Nodular iron, 1-piece rear main seal
    • Connecting Rods: Powdered metal
    • Pistons: Cast aluminum
    • Camshaft Type: Hydraulic roller
    • Camshaft Lift: .473" intake / .473" exhaust
    • Camshaft Duration (@.050 in.): 215° intake / 223° exhaust
    • Cylinder Heads: Vortec cast iron, 64cc combustion chambers
    • Valve Size: 1.940'' intake / 1.500'' exhaust
    • Compression Ratio: 9.0:1
    • Rocker Arms: Stamped steel
    • Rocker Arm Ratio: 1.5:1
    • Recommended Fuel: Premium pump
    • Ignition Timing: 32° Total @ 4000 rpm
    • Maximum Recommended RPM: 5600
    • Balanced: External
    • Flexplate: 12.750"

    GM Warranty

    JEGS Easy Kits are designed by JEGS high-performance racing professionals to help you get all the performance parts you need for your race car, hot rod or truck.

    Does this engine have provisions for a mechanical fuel pump?

    Asked by: Hman
    Yes, this engine has the mechanical fuel pump boss on the block.
    Answered by: Rusty B
    Date published: 2018-06-29

    Will Chevrolet Performance Small Block V8 or V6 Rocker Arm Kits 19210728, install and work in GM SP350 CI 357 HP Base Crate Engine # NAL-19367080 Engine Assembly, with out any other parts or modifications, other than required tall valve covers ?

    Asked by: BobbyH
    Yes, these rocker arms will work in your engine.
    Answered by: Rusty B
    Date published: 2018-03-11
    • y_2019, m_10, d_13, h_6CST
    • bvseo_bulk, prod_bvqa, vn_bulk_2.0.13
    • cp_1, bvpage1
    • co_hasquestionsanswers, tq_2
    • loc_en_US, sid_10001_10001_5391498, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs

    Easy Kits

    Items You Need

    Some parts are not legal for use in California or other states with similar laws / regulations

    Motor Vehicles

    WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.

    Tools:

    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

    Electrical Cords

    WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.