Special Notes:

• The Stinger RC Buggy does not come with a battery or a charger. This buggy is compatible with NiMH and 2S-3S LiPo batteries. These units must be purchased separately. See Below.
• JEGS RC Vehicles come set up for a LiPo Battery. When upgrading to a NiMH Battery you will need to adjust the pin location on your motor to the NiMH Battery setting during installation or serious damage may occur to your unit. See the Illustration in the images above for the correct pin adjustment.
• Chargers
  • 60W Rapid balance charger - 555-45000
  • 20W Sport balance charger - 555-45010
• Batteries
  • Nickle-Metal Hydride
    • NIMH 8.4V-3K MAH 7-Cell, Hump-Pack - 555-45050
  • Lithium-Polymer
    • LIPO 2S 7.4V 5KMAH 2-Cell - 555-45080
  • The LIPO 3S 11.1V 5KMAH 35C battery DOES NOT FIT.
• The Pistol-Grip Controller requires 4 AA batteries not included.

JEGS Stinger RC Buggy Replacement Parts CLICK HERE

JEGS RC Batteries CLICK HERE

JEGS RC Battery Chargers CLICK HERE

JEGS RC Battery Charger Accessories CLICK HERE

Explore the path less traveled with the JEGS 44100 Stinger RC Buggy. Designed for performance and personalization, the Stinger features a high-torque electric motor and fully-customizable control settings.

The Stinger uses front and rear independent suspension, coil-over shocks, and aggressive tire tread to outrun the competition in any terrain. This RC car is also designed with a sleek body and contrasting yellow and black paintwork. The rear wing adds stability while enhancing its overall look.

555-44100 Stinger RC Buggy Features

• Dimensions
  • Overall: 16.200 in. L x 9.450 in. W x 5.150 in. H
  • Ground clearance: 1.730 in.
  • Battery tray dimensions: 5.500 in. L x 1.875 in. W x 1 in. H
• Wheels:
  • Front: 2.200 in. D x 1 in. W
  • Rear: 2.200 in. D x 1.500 in. W
• Weight: 3.700 lbs.
• Tires:
  • Front: Grooved (3.250 in. D x 1.062 in. W)
  • Rear: Knobby (3.375 in. D x 1.625 in. W)
• Servo
  • 6kg Servo
  •  Torque
    • 4.8V: 10.0 kg 138.8 oz./in.
    • 6V: 12.0 kg 166.7 oz./in.
  • Speed
    • 4.8V: 0.16 sec/60 degrees
    • 6V: 0.14 sec/60 degrees
• ESC (Electronic Speed Control)
  • Waterproof (With the exception of prolonged submergence)
  • Dustproof
  • Built-in capacitor
  • Programmable with jumpers
• Drivetrain
  • Rear mounted engine
  • Axle shafts: 5mm hardened steel
  • Gearbox:
    • Performance slipper system
    • Changeable gearing
    • High-efficiency design
    • Precision metal ball bearings
  • Bevel gear type differential
  • Sealed axle housings
  • Slipper clutch
• Chassis
  • Double wishbone suspension front and rear
  • Multiple shock mounting points to adjust suspension
  • Sealed compartment for the receiver
  • Philips screw hardware is used throughout
  • Quick-release velcro battery holder
  • 2 mounting posts to secure the body
  • Impact-resistant plastic composite
• Suspension
  • Shocks: (4) Oil-filled big-bore coil-overs (1 per corner)
    • Shock body: 10 mm OD
    • Shaft: Hardened polished steel (3 mm OD)
    • Performance Spring Rate
  • Axles: Independent front and rear
• Electronics
  • Servo: 12 kg
  • Electronic Safety Features
    • Over-heating prevention
    • Throttle signal loss protection
• Pistol-Grip Controller
  • Requires 4 AA Batteries Not Included 
  • Frequency: 2.4 GHz
  • Adjustments:
    • Security
      • Lock/unlock 
    • Steering
      • Servo reversal (Reverse steering control)
      • End-point (Increase or decrease maximum steering angle)
      • Digital trimming (Adjusts steering to a neutral position when not moving)
      • Dual-rate (On-the-fly adjustments)
    • Throttle
      • Throttle reverse (Reverse controls)
      • End-point (Increase or decrease maximum throttle input)
      • Braking (Increase or decrease braking force)
      • Digital trimming (Adjust the throttle in the neutral position when not moving)