Account Login
Gift Cards
Track Order
Help Center

JEGS Flexible Braided Transmission Dipstick for GM 4L60E [Polished]


Product Q&A
View Now
Click image to zoom
Flexible Braided Transmission Dipstick for GM 4L60E [Polished]
SAVE $6.00
9 left in stock
Flexible Braided Transmission Dipstick
  • GM 4L60E
  • Firewall Mount
  • Stainless Steel Braided Hose
  • Polished Billet Aluminum Handle
  • Double O-Ring Seal
  • "Add" & "Full" Markings
  • Includes Funnel Adapter
  • Ships

    Items You May Also Consider

    615953 is rated 4.2 out of 5 by 11.
    Rated 5 out of 5 by from Looks Amazing! I bought this for my 4.8 swapped 89 s10 and it looks great, and it works great!
    Date published: 2019-03-27
    Rated 5 out of 5 by from Works well Well made and easy to install. Not very tight going into the case so I applied some RTV just to be safe.
    Date published: 2018-12-28
    Rated 5 out of 5 by from Flexible Installation Under tight component spacing, this dipstick takes care of all issues. I opted for inside fender mounting. Installation in the transmission was easy and leak-free with double o-ring seals. Looks good with other SS braided lines in the engine bay.
    Date published: 2017-10-27
    Rated 4 out of 5 by from Nicely built, good quality.....but I'm using this 555-615953 tranny dipstick with a 4L65e tranny. The 2 o-rings that seal the bottom to the tranny leaked. After pulling things apart I found the o-rings were the wrong size. I replaced them with #113 viton o-rings which have a slightly thicker CS (that's wall thickness). It now has a tight fit. I would have given it 5 starts if I didn't need to replace the o-rings and clean the leaks off the garage floor.
    Date published: 2019-11-03
    Rated 3 out of 5 by from Did not fit 2001 4L60e 2WD Purchased this item for a LS/4L60 swap with little engine bay room, the push fit would not fit my 4L60e from a 2WD 2001 Chevy 1500. the nut part of the fitting that goes into the pan was too large and would not clear the side of the trans case. I liked the quality of the piece but it may not fit all 4l60e transmissions.
    Date published: 2020-04-16
    Rated 3 out of 5 by from 2000 Blazer 4x4 LQ4 Swap - Stock 4L60E I purchased this dipstick due to swapping engines and not finding a suitable replacement for the engine / transmission combination I am using. I noted the following when I received and installed the dipstick. 1. Funnel adapter machined incorrectly, does not fit in dipstick tube. 2. O-rings have a loose fit in transmission. 3. Needed to grind away casting boss on transmission for dipstick to fit. I was not going to grind the dipstick I just paid $45 for. Still needed to tap into transmission with a wooden dowel. Overall, it was not easy to install and may leak due to poor fitting O-rings. It did not leak when putting the first 4 quarts of ATF in the transmission.
    Date published: 2020-01-03
    Rated 2 out of 5 by from The clear plastic fill tube and fitting The fill tube adapter needed to be removed and reversed because it would not fit into the braided steel fill tube the small metal bushing has two different diameters. The large fitting on the transmission end needed to be clearances to fit and the o rings could be thicker
    Date published: 2020-04-24
    • y_2023, m_3, d_24, h_22
    • bvseo_bulk, prod_bvrr, vn_bulk_3.0.34
    • cp_1, bvpage1
    • co_hasreviews, tv_4, tr_7
    • loc_en_US, sid_10001_10001_3301038, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs

    I have a 2004 silverado and wanna make sure this will work before I buy it?

    Asked by: Tim1996
    Yes, this will fit that application.
    Answered by: Rusty B
    Date published: 2017-09-06

    What is the length of this part?

    Asked by: Jamesd1
    30" overall. Below is a diagram with lengths http://www.jegs.com/jegs/jegsbraideddipsticks.html
    Answered by: Flanary
    Date published: 2020-11-16
    • y_2023, m_3, d_23, h_22CST
    • bvseo_bulk, prod_bvqa, vn_bulk_3.0.34
    • cp_1, bvpage1
    • co_hasquestionsanswers, tq_2
    • loc_en_US, sid_10001_10001_3301038, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs

    Items You Need

    Recently Viewed

    Some parts are not legal for use in California or other states with similar laws / regulations

    Motor Vehicles

    WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.


    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

    Electrical Cords

    WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.