Order Status & Returns
Gift Cards
Help Center
1-800-345-4545
Vehicle Info Needed
Lowest Price GuaranteeBrandACDELCO
Package Height0.5
Package Width0.5
Package Length9.0
Weight0.2 PG
Good Maintenance Practices - Section 2 - Bullet 3Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4Parking brake adjustments (as needed).
Fitting MaterialSteel
Programming RequiredNo
End 2 Thread Diameter (Mm)10
Good Maintenance Practices - Section 2 - Bullet 1Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Good Maintenance Practices - Section 2 - HeaderThe following should be conducted by a qualified technician:
End 2 Flare TypeInverted
Signs Of Wear & Troubleshooting - Section 1 - Bullet 1Brake pedal pulsation (not to be confused with normal ABS operation).
Fitting FinishZinc Chromate
Pre-FormedYes
Good Maintenance Practices - Section 1 - Bullet 1Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Teflon LinedNo
Good Maintenance Practices - Section 1 - Bullet 4Check the thickness of your brake pads.
Inside Diameter3.36
Good Maintenance Practices - Section 1 - Bullet 2Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Features & Benefits - Bullet 2GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
Meets Or Exceeds Original Equipment Manufacture SpecificationsYes
Features & Benefits - Bullet 3GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Fitting TypeFlare
Features & Benefits - Bullet 4GM regularly updates production and service part designs to integrate new materials and technologies
Outer Wear GuardNo
Product DescriptionGM Genuine Parts Brake Hydraulic Lines are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These are quality reinforced lines that carry fluid within the brake system. The hydraulic fluid must travel to the wheel brakes from the master cylinder. It does this through brake lines or pipes and brake hoses. Brake lines and hoses are designed to withstand high pressures. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE). ⚠<b> WARNING:</b> Cancer and Reproductive Harm - www.P65Warnings.ca.gov
End 1 Thread Diameter (In)0.39
Features &#38; Benefits - Bullet 1Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
End 1 Thread Diameter (Mm)10
End 1 Flare TypeInverted
Good Maintenance Practices - Section 1 - HeaderThe following inspections and maintenance procedures can help prevent potential brake problems.
Width (In)0.95
Polyvinyl Fluoride CoatedNo
Line MaterialSteel
Line Length436.26
Height (In)0.3
Signs Of Wear &#38; Troubleshooting - Section 1 - Bullet 2Vehicle pulls to the left or right when brakes are applied.
BendableNo
Length (In)1.6
End 2 Thread Diameter (In)0.39
Line Diameter0.205
Outside Diameter5.2
Outer SpringNo
Weight (Lb)0.005
Grade TypeOE
Vendor Part Number95091330
Package Qty1
Package TypeEA
No Questions
No Reviews
Some parts are not legal for use in California or other states with similar laws / regulations
