$5 off $49+/$20 off $249+/$60 off $499+/$120 off $999+* Use Promo Code: EARLY26

New Item Badge
SB-3540R Rear Sway Bar for 1935-1940 Ford
InfoVehicle Info Needed
CHASSIS ENGINEERING INC.PART NUMBER: 141-SB-3540R

SB-3540R Rear Sway Bar for 1935-1940 Ford

$30700
ShippingShips on 11/27/2026
Lowest PriceLowest Price Guarantee

Items You Need

Lo Boy Creeper 250 lb. Capacity

JEGS

Lo Boy Creeper 250 lb. Capacity

Part Number : 555-81154
$5999$65.99
You Save$6.00
123-Piece Tool Set with Carry Case

JEGS

123-Piece Tool Set with Carry Case

Part Number : 555-80427
$3199$51.99
You Save$20.00
2-Ton Low-Profile Aluminum Floor Jack [4,000 lbs. Capacity]

JEGS

2-Ton Low-Profile Aluminum Floor Jack [4,000 lbs. Capacity]

Part Number : 555-80006
$19599$269.99
You Save$74.00
6-Ton Jack Stands

JEGS

6-Ton Jack Stands

Part Number : 555-80037
$6479$89.99
You Save$25.20

Ford
    Rear Sway Bar
  • For 1935-1940 Ford

    Chassis Engineering SB-3540R Features:

    SB-3540R Rear Sway Bar for 1935-1940 Ford. This rear sway bar fits Chassis Engineering rear end kits for the 1935-1940 Fords. This is an excellent way to improve the handling and overall driveability of your street rod. Sway bars work best when you have both the front and rear bars. All linkage and mounting furnished.

    Installation Instructions for Rear Swaybar for 1935-40 Ford using parallel leaf suspension

    Note: Use of Chassis Engineering rear end mounting kit (AS-2016C, link) recommended.

    Step 1: Remove the two lower rear rivets that connect the rear crossmember to the frame.

    Drill holes out to 3/8 in.. Hold frame brackets in place and mark second hole (Note: a shock reinforcement plate may interfere with the next hole). Drill hole to 3/8 in.. Hole can be misaligned to clear.

    Step 2: Place €œD€ shaped rubber bushing on bar, in-line with the mounting holes. Install the frame brackets over bushing. Bolt through brackets and frame.

    Step 3: All Chassis Engineering kits after Aug 1st, 1982 will have bottom sway bar mount as a standard feature. Earlier kits should be changed. On other applications not using Chassis Engineering lower shock plates, a 5/8 in. hole must be located 47 3/4 in. apart on brackets.

    Step 4: Assemble linkage as shown below. Do not over-tighten.

    Chassis Engineering Sway Bars For Better Handling And Reduced Road Sway

    Chassis Engineering sway bars are built to improve handling, drivability, and stability for classic cars, trucks, hot rods, and performance builds. Available in front, rear, universal, and vehicle-specific kits, they include linkage and mounting hardware to simplify installation and help reduce body roll. With steel construction, sttractive finishes, and applications for Ford, GM, and universal setups, these sway bar kits are a trusted suspension upgrade for tighter control and a more confident ride.

Part TypeSway Bar
Product LineChassis Engineering Sway Bars
BrandCHASSIS ENGINEERING INC.
Package Height4.0
Package Width17.0
Package Length51.0
Weight17.0 PG
Part CategoryPerformance Parts
Part FitmentSemi Universal
Vendor Part NumberSB-3540R
Package Qty1
Package TypeEA
No Questions
No Reviews
Some parts are not legal for use in California or other states with similar laws / regulations
p65 warning