Order Status & Returns
Gift Cards
Help Center
1-800-345-4545
Product Discontinued
Currently Unavailable
This product is no longer available. Please call customer service for assistance at 1-800-345-4545.
- Disc Brake Caliper Bolt
Part TypeBolt
BrandACDELCO
Package Height1.2
Package Width1.6
Package Length103.5
Weight0.03 PG
Part CategoryReplacement Parts
Head Tool Size (Mm)18
Rear Brake TypeVarious - Application Specific
Body TypeVarious - Application Specific
Good Maintenance Practices - Section 2 - Bullet 3Inspection of wheel bearings and grease seals.
Good Maintenance Practices - Section 2 - Bullet 4Parking brake adjustments (as needed).
PositionFront
Brake SystemVarious - Application Specific
Programming RequiredNo
Front Brake TypeVarious - Application Specific
Good Maintenance Practices - Section 2 - Bullet 1Inspection of the brake hoses for brittleness or cracking.
Good Maintenance Practices - Section 2 - Bullet 2Inspection of brake lining and pads for wear or contamination by brake fluid or grease.
Number Of DoorsVarious Application Specific
Thread Pitch (In)1.5
Good Maintenance Practices - Section 2 - HeaderThe following should be conducted by a qualified technician:
Signs Of Wear & Troubleshooting - Section 1 - Bullet 1Brake pedal pulsation (not to be confused with normal ABS operation).
Good Maintenance Practices - Section 1 - Bullet 1Check brake fluid level at every oil change. Replace fluid according to owner's manual recommendations.
Thread Length (In)1.24
Heat HardenedYes
Good Maintenance Practices - Section 1 - Bullet 4Check the thickness of your brake pads.
Thread Length (Mm)31.5
Good Maintenance Practices - Section 1 - Bullet 2Calipers and wheel cylinders should be checked every brake inspection and serviced or replaced as required.
Good Maintenance Practices - Section 1 - Bullet 3Inspect the brake lines for rust, punctures, or visible leaks (You may be able to do this, but consult a qualified technician if necessary).
Features & Benefits - Bullet 2GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
Features & Benefits - Bullet 3GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
Features & Benefits - Bullet 4GM regularly updates production and service part designs to integrate new materials and technologies
Product DescriptionGM Genuine Parts Disc Brake Caliper Guide Pins are designed, engineered, and tested to rigorous standards, and are backed by General Motors. The guide pin is responsible for maintaining the proper brake pad angle within the caliper, allowing proper contact with the rotor. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE). ⚠<b> WARNING:</b> Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Features &#38; Benefits - Bullet 1Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
Bolt TypeHex Flanged Head
Head Drive TypeHex Flanged Head
Good Maintenance Practices - Section 1 - HeaderThe following inspections and maintenance procedures can help prevent potential brake problems.
Width (In)1.1
MaterialSteel
Grade10.9
Thread Diameter (Mm)16
Washer AttachedNo
Thread Diameter (In)0.63
S.A.E. Or MetricMetric
Height (In)1.1
Signs Of Wear &#38; Troubleshooting - Section 1 - Bullet 2Vehicle pulls to the left or right when brakes are applied.
Part FitmentDirect Fit
Weight (Lb)0.03
Grade TypeOE
Vendor Part Number179-711
Package Qty1
Package TypeEA
No Questions
No Reviews
Some parts are not legal for use in California or other states with similar laws / regulations
