
Performer 2-0 Power Package Intake Manifold, Carburetor and Camshaft Kit Big Block Chevy 396-502ci - Oval Port
- Performer 2-0 Power Package
- Big Block Chevy 396-502ci - Oval Port
- 4-bbl Spread-Bore Carb Flange (non-EGR)
- Idle-5500 rpm
- Designed for street 396-502 c.i.d. big-block Chevy V8s using general duty oval-port cylinder heads.
- Will fit 1965-90 oval port heads.
- For 396, 402, 427 and 454 V8s with OEM 4-bbl. carb.; 1965-72 (1973 non-CA) passenger cars and 1966-83 trucks, Suburbans and heavy vehicles; except stock equipped EGR. (Intake manifold p/n 350-3761 is for 454 V8s with OEM 4-bbl. carb.; 1972-89.
- Will not fit under hood of Corvette without hood modifications.
- Will not fit 'tall block' V8s.
- May be used with OEM or aftermarket carbs.
Power Package includes matching:
- Performer 2-0 Intake Manifold 350-2161
- Edelbrock Performer 750cfm Carburetor 350-1411
- carb square flange adapter plate 350-2732
- Performer-Plus Hydraulic Flat Tappet Camshaft & Lifters 350-2162
Installation Notes:
- Port exit dimensions: 1.70' x 1.68'
- Recommended intake gasket: Edelbrock 350-7203, Fel-Pro 375-1212, Mr.Gasket 720-107 Standard Seal, 720-5827 Ultra Seal, 720-820G Ultra Seal II.
- Manifold height: (A) 4.30' , (B) 5.40'; Carb pad height = 4.85'
- View Manifold 'A/B' Measurement Guide.
- Choke adapter 350-8961 is included.
- Use water neck adapter 350-8028 with 1986 & later.
Carburetor Recommendations:
OEM Rochester Quadrajet 4-bbl.
- will work with non-EGR system
- use Automatic Divorced Choke Rod 350-9179 with Q-jet carb.
Edelbrock Performer 600cfm Carburetor 350-1405 or
Edelbrock Performer 750cfm Carburetor 350-1407 good for towing over 10,000 lbs. or
Edelbrock Performer 800cfm Carburetor 350-1412 good for towing over 10,000 lbs. or
Edelbrock Thunder Series AVS 650cfm Carburetor 350-1805 or
Edelbrock Thunder Series AVS 800cfm Carburetor 350-1812 good for towing over 10,000 lbs.
- will work with non-EGR system
- has no provision for evaporative canister,
- requires 350-8008 or 350-8024 stud, nut & washer kit
- acceptable to factory cruise control.
- has manual choke only.
- use carb square flange adapter plate 350-2732.
Edelbrock Performer 600cfm Carburetor 350-1406 or
Edelbrock Performer 750cfm Carburetor 350-1411 good for towing over 10,000 lbs. or
Edelbrock Performer 800cfm Carburetor 350-1413 good for towing over 10,000 lbs. or
Edelbrock Thunder Series AVS 650cfm Carburetor 350-1806 or
Edelbrock Thunder Series AVS 800cfm Carburetor 350-1813 good for towing over 10,000 lbs.
- will work with non-EGR system
- has no provision for evaporative canister,
- acceptable to factory cruise control.
- use carb square flange adapter plate 350-2732.
Camshaft Specs:
In order to use these camshafts in 1965-66 396/427ci blocks, it is necessary to machine a 3/16' wide x 7/64' deep groove in the rear main journal of the cam to allow oil flow to the top of the engine.
- Designed for optimum torque from the low-end to the mid-range.
- They are smooth idling cams for daily drivers, trucks, vans, RVs and 4x4s.
- You can expect a major improvement in throttle response and torque.
Note: For computer controlled vehicles using Edelbrock intake manifold 350-3764. Not legal for sale or use on pollution controlled motor vehicles.
Duration Advertised: 292° Intake / 302° Exhaust Duration @ .050' Lift: 218° Intake / 228° Exhaust Valve Lift: .500' Intake / .500' Exhaust Lobe Separation Angle: 114° Open/Close @.050' Cam Lift: Intake - 0° ATDC (opens) / 38° ABDC (closes)
Exhaust - 53° BBDC (opens) / 5° BTDC (closes)Emissions Note:
This part is only legal for sale and use on Uncontrolled (Non-Emissions Controlled) Vehicles or on vehicles used solely for the purposes of closed competition racing.
CLICK THIS LINK FOR IMPORTANT CARB & EPA EMISSIONS INFORMATION ABOUT THIS PART
Intake Manifold, Carburetor and Camshaft Kit




