Danchuk 10100 Engine Starter Plate for 1955-1956 Chevy Tri-Five with Small Block Chevy 265 V8 with Late Model Transmission
241-10100
Starter Plate
Danchuk 10100 Engine Starter Plate Features:
- Starter plate provides an original mounting style for 265 Chevy V8 that has no mounting provision.
- Engine starter plate is a must have when upgrading to a late model GM transmission that never had a starter mount. (ex. TH350, TH400, 2004R, 700R4)
- Can be used in 1957 models that have broken starter mounts. Will require a 1955-1956 style starter.
- Requires a 168 tooth flexplate
FAQ
Can I replace a starter myself?
Yes, you can replace a starter yourself, and the Danchuk 10100 engine start plate, commonly known as the Danchuck starter plate, can assist in simplifying this process for Chevy engines. The starter plate plays a crucial role in providing a mounting point for the starter motor, ensuring proper engagement with the flywheel. With the Danchuck 10100 starter plate, DIY enthusiasts can easily replace a starter, enhancing the overall efficiency and performance of their Chevy engine.
What are the steps necessary to replace a starter?
Replacing a starter involves several key steps. Begin by disconnecting the vehicle's battery to ensure safety. Locate the starter and remove the electrical connections and mounting bolts. Install the new starter and reattach the electrical connections. The Danchuk 10100 engine start plate facilitates this process for Chevy engines, providing a reliable mounting solution. Always refer to the vehicle's service manual for specific instructions and torque specifications during the replacement process.
Can you test a starter without removing it?
Yes, you can test a starter without removing it. Use a multimeter to check the voltage at the starter's electrical connections while attempting to start the engine. If the voltage is within the specified range and the starter still fails to engage, there may be an issue with the starter itself. The Danchuck 10100 starter plate for Chevy engines ensures proper alignment and mounting, contributing to the starter's efficient operation and facilitating easier testing procedures.
How do you start a car with a bad starter?
Starting a car with a bad starter temporarily can be done using alternative methods. One common technique is to tap the starter motor with a tool while turning the ignition key. This may provide enough momentum for the starter to engage. Keep in mind that this is a temporary solution, and it is recommended to replace the faulty starter as soon as possible. The Danchuk 10100 engine start plate offers a reliable mounting solution for Chevy engines, ensuring optimal starter performance and reducing the likelihood of such issues.
Looking for one that will fit a 8.1 chevy silverado HD 2001 any leads
Will this work on a 94’ gmc 2wd 6.5 diesel with the 4l80e?
Will this work on 1996 chevy k1500 with 5.0 engine
Will this work on a 77 400sbc with a granny low four speed
So this kit will not work on a 4L60? My block is broken on the outer hole where the starter mounts! This would be great if it would do the trick?
Will this work on a 2000 chev 4X4 3500 5.7? it has a one rear main seal.
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.