Unrivaled Customer Service
And Expert Tech Advice!  
Same Day Shipping Before 11 PM ET
My Cart
Shop By Vehicle
Shop By
Close Menu
Shop By Vehicle
Top Categories
All Categories

Top Categories

All Categories

Free Catalog
E-Mail Signup
My Account
Track Order
Gift Certificates

Global West Upper Control Arms 1973-77 A-Body

Global West TLC-37


made in usa
jegs shipping
FREE Shipping
Estimated to ship directly from the manufacturer on 10/04/18
Easy Returns
Easy Returns
Lowest Price Guarantee
Lowest Price Guarantee
Global West Upper Control Arms 1973-77 A-Body $496.99
Upper Control Arms
1973-77 A-Body

Global West TLC-37 Details

General Motors


  • 1973-77 Buick Century/Regal
  • 1976-79 Cadillac Seville
  • 1973-77 Chevy Chevelle/El Camino/Malibu/Monte Carlo
  • 1973-77 Oldsmobile Cutlass/442
  • 1975-79 Oldsmobile Omega
  • 1973-77 Pontiac Lemans/T-37/GTO
  • 1975-77 Pontica Ventura
  • 1977-79 Pontiac Phoenix

  • Specifications:

    Manufacturer's Part Number:

    Drag Race Dedicated Suspension Systems
    Lightweight tubular upper control arms are fully assembled with billet aluminum cross shafts, special Delrin bushings, ball joints, and shortened bump stops. The upper arms are made out of 4130 chrome-moly to reduce front-end weight.

    Geometry Change - Nothing But Positive
    One of the biggest problems most production cars have is not enough caster. Caster provides staight-line stability and reduces wander at high speeds. It is part of the front end self-aligning force. For this reason, caster is essential on drag cars. Unfortunately, there is never enough caster available using stock front-end components. Too many alignment shims are needed and possible camber problems can occur. TLC upper control arms are built with additional positive caster and steeing camber is never a problem.

    Control Arms Shafts
    All TLC upper control arms use billet aluminum cross-shafts. Steel sleeves are pressed in on each side of the shaft for protection. The sleeves isolate the aluminum shaft from alignment shims, frame bolts and nuts. This allows proper torque to be maintained on the cross-shaft. Without steel sleeves, alignment shims and upper shaft bolts would rest against the aluminum shaft and eventually work loose. Once the bolt works loose, alignment shims would fall out causing loose alignment.

    Bump Stops
    Bump stops are installed on the upper control arms to stop ball joint over travel. This protects the upper ball joint from damage. Sometimes, if the front end travel needs to be limited, the bump stop may be removed and a limiter may be added in its place.

    TLC control arms use Delrin type bushings machined specifically for Global West's shafts and housings. Delrin is a hard plastic and can handle extreme loads associated with suspension components. It is long lasting and very durable. Grease fittings are installed in the control arms for lubricating the bushings. Synthetic grease is recommended.

    TLC Lower Control Arms
    TLC lower arms are similar to the G-Plus lower control arms. The TLC arms have no sway-bar attachment points or additional plates in order to lighten the arms. The arm is considered a load carrier and is ''beefed up'' to handle wheel stands and extreme loads. Weight savings is minimal using the lower arm because of the tubing wall thickness required.

    Sold in Pairs

    Items You Need
    Some parts are not legal for use in California or other states with similar laws / regulations

    Motor Vehicles

    WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.


    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

    Electrical Cords

    WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.