0
0
×
Account Login
1-800-345-4545
Gift Cards
Track Order
Help Center

JEGS Regulator Mount with Hard Line For 4150 carburetors

555-15081

made in usa

Product Q&A
View Now
Click image to zoom
Regulator Mount with Hard Line For 4150 carburetors
$86.99
$78.99
SAVE $8.00
More than 10 available
Regulator Mount with Hard Line
  • For 4150 carburetors
  • JEGS, Holley, Quick Fuel regulator
  • Made in the USA
  • Ships
    QTY
    15081 - JEGS Regulator Mounts & Regulator Kits is rated 2.3 out of 5 by 4.
    Rated 3 out of 5 by from Hope it works Bought the kit, all jegs products, the 2 supplied screws were not long enough to connect the jegs supplied regulator to the jegs bracket, which makes no sense. Had to find my own to make it work. No supplied instructions. Bracket is well made and fittings seem to be nice quality.
    Date published: 2024-11-17
    Rated 1 out of 5 by from Do Not Buy This Bracket The picture shows this installed on a carburetor with vacuum secondaries, but with the regulator installed like what is in the picture, the regulator hits the vacuum actuator, and the bracket blocks the vacuum port below the vacuum actuator. There are no install instructions, so everything is trial and error (mostly error). I tried flipping the bracket, and that moved the regulator forward enough that it wasn't rubbing against the vacuum actuator, but the bracket was still too close to the vacuum port, and the hoses in the kit don't line up properly. I bought the kit that included the regulator, so there were an extra set of regulator mounting screws that were long enough to mount the regulator to the bracket, but the screws were the wrong diameter and pitch, so I had to make a trip to the hardware store to get screws that fit. Also, the regulator does not come with a fitting to connect the inlet side to the fuel line, so I had to buy an extra fitting as well. Great idea, but overall horrible execution. Now I am out over $120 with nothing to show for it, and it's looking like I'd be better off trying to build a mount for this myself.
    Date published: 2024-12-05
    Rated 1 out of 5 by from horrible leaks Bought first one in 2016. Has always leaked (sometimes see/sometimes drip) at front carb side fitting where line seals with AN fitting. Nothing would ever fix. Finally bought new complete kit. It was leaking at 3 of 4 places where line seals with AN. Inspection shows quite rough flare. Jegs is taking back the second kit, and I have since replaced the hard lines with braided hose, using the same regulator bracket and the same AN fittings into the carb and the regulator - just minus the hard lines. No longer any leaks.
    Date published: 2018-02-27
    • y_2025, m_2, d_7, h_6
    • bvseo_bulk, prod_bvrr, vn_bulk_3.0.42
    • cp_1, bvpage1
    • co_hasreviews, tv_1, tr_3
    • loc_en_US, sid_10001_10001_353382, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs

    Will a Holley Fuel Pump Regulator, p/n 510-12-887 bolt up to this Jegs Regulator mount or Holley Regulator 510-12-887 same mounting pattern as Jegs Regulator 555-15912?

    Asked by: Will
    The Jegs 555-15081 bracket will work with a Holley regulator.
    Answered by: jshook
    Date published: 2024-03-08
    • y_2025, m_2, d_7, h_6CST
    • bvseo_bulk, prod_bvqa, vn_bulk_3.0.42
    • cp_1, bvpage1
    • co_hasquestionsanswers, tq_1
    • loc_en_US, sid_10001_10001_353382, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_jegs

    Easy Kits

    Related Products

    Fits 1979-2004 ford mustangSimplifies the installation of a lightweight polyethylene or aluminum seatDesigned for bottom mount seats but can be used with side mount seats with the purchase of side mount seat bracketsSpecifications: 3/16” thickMade in usa with high quality ...
    Close
    JEGS 555-90619 Trunk Latch Mount Features:Replacement mount is made to the original specifications for easy installationCorrect factory contours for an authentic look and fitRetains factory mounting points. Chevelle.
    Close
    Allows installation of two coil-over shocks on any car utilizing rear end housings with 3 inch o.d. axle tubesWelding required to complete installationAllows 6 inches of height adjustmentIncludes (2) 1/4 in. housing brackets, (2) 3/16 in. shock brackets, (4) spacers, ...
    Close
    Some parts are not legal for use in California or other states with similar laws / regulations

    Motor Vehicles

    WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.

    Tools:

    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

    Electrical Cords

    WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.